Being part of the Flip-Pal™ mobile scanner blog hop has encouraged me to try new things. I’m searching high and low for things to scan because I love it. The canvas I Podged above is a great example. I’ve never done a DIY knock-off before, and then I saw something so outrageously priced in a Ballard Designs catalog that I had to give it a go. My problem was that I needed a pattern because I could tell that if I winged it, the whole project was going to go terribly wrong. I needed to do some enlarging. An easy job for my buddy the Flip-Pal:
You might be laughing that I need a pattern for something so simple, but that’s just how I roll. I can’t freehand stuff unless it’s my own design. One minute the drawing hand is on a straight path, the next minute it’s off in Timbuktu. Sad, huh?
See that dress above? That giclee print that retails for $299? That was my inspiration. My resulting project is not quite as big, but I didn’t want it to cover an entire wall. I just wanted to enlarge the picture enough to make a pattern. So I did.
Before I begin, here are the rules of knock-offs. You can make a knock-off for personal use only; you can’t sell or claim it as your own. Doing so would be like crossing proton streams in Ghostbusters. It would be bad. If you’d like to do your own version of this giclee, here’s how.
Gather These Supplies
Flip-Pal™ mobile scanner
Computer and printer
Image to scan
9″ x 12″ canvas
Mod Podge Satin
Mod Podge Dimensional Magic
FolkArt acrylic paint – Fuchsia, Parchment (or coordinating colors)
Scrapbook paper – I used three sheets of K and Company Flora and Fauna by Brenda Walton
Wood circles – 3 small ones for buttons
Craft knife and mat
Scan the catalog on your Flip-Pal. Here’s how to blow the image up – scan at 600 dpi. Um, love this feature! I’m about to make a big pattern. What I did was save the image into my photo software, and blew it up to fit my 9″ x 12″ canvas. Just so you know, the 600 dpi setting is so great that I could have enlarged it even more. I printed two copies since I knew that I would be cutting up one, so I wanted to have a spare for an extra pieces.
Tape your pattern down to your scrapbook paper. As you can see, I found some random skinny tape. It doesn’t matter what kind of tape you use, really. Use your craft knife to begin cutting out the pieces, using the pattern as a template.
I used my second pattern on my coordinating piece of scrapbook paper. I cut out the sleeves and the inner folds of the dress. Set your paper pieces aside.
Paint your canvas with Parchment (or your coordinating color). Give several coats and allow to dry.
Paint your wood buttons with the Fuchsia paint. You can see that I use paint plates over and over again. I put new paint over the top of the old paint too. I feel like I’m letting you see into my laundry hamper.
Lay the design out onto the canvas. Mod Podge the pieces down by spreading a medium layer of glue and then smoothing out the paper on top of it. Repeat until all of the pieces are down, then allow to dry for 15 – 20 minutes. Mod Podge over the top to seal. Allow to dry and then add another coat of Mod Podge.
Tip: I wanted to do a bit of a different belt that then one from Ballard, so I left a gap between the top of the dress and the skirt when I Mod Podged everything down. This will obviously be covered.
Add a ribbon belt and a coordinating embellishment for a little “flair.” Glue down the buttons as well. After a little debate, I decide to add some Dimensional Magic to the top of the buttons. It really worked to add some interest.
I love my knock-off art! I’m not only looking around and wondering what I can scan, but I’m looking around and wondering what I can knock-off. Speaking of knock-offs, check out this other version of the same piece done by Susan at Living With Punks. She used fabric. Isn’t it fun? Click here for her tutorial.