Skip to Content

DIY Jewelry Organizer from a Cup Holder

Organize your baubles on a budget with this DIY jewelry organizer made from a cup holder! All you need is paint, Mod Podge, and paper.

DIY jewelry organizer from a cup holder

Shannon from Rosyscription is especially great at budget projects and revamping thrift store finds. Her latest project, this DIY jewelry organizer, is useful and cute . . . you’re going to love it!

I’m always on the lookout for ways to make storage solutions pretty. For some reason, I find it much easier for me to keep things neat and clean if the storage area looks cute.

Recently, I’ve been searching for a way to keep my jewelry tidy in my bedroom. My bracelets seem to have a bad habit of wandering off. They are never around when I need them!

cup-holder-stand-thrifting

So, I was thrilled when I found this simple, wooden coffee cup holder at a thrift store recently. I knew that all it would take was a coat of paint and some cute paper to make it into an adorable stand for my bracelets.

I have a rather large collection of scrapbook paper and I thought it would be pretty to make a striped paper effect on the bottom of the stand. (and it was easier to work with the paper in small pieces versus one large circle that would have been difficult to cut exactly).

base-for-bracelet-holder-storage

Want to know how to make a cute jewelry rack? Just follow the steps below.

Step one: Gather your supplies.

  • Wooden coffee cup holder
  • Spray paint
  • Mod Podge Satin
  • Pretty paper
  • Foam brushes
  • Scissors
  • Circle paper punch

Step two: Prep and paint the cup holder.
Clean the mug stand and spray it with several light coats of spray paint. Allow the paint to dry thoroughly.

TIP: I was able to separate the top and bottom pieces of my cup holder. I loosened them prior to painting so that the stand could easily be taken apart later without scratching up the paint job.

Step three: Cut strips of paper for the base and attach them with decoupage.

how-to-make-bracelet-holder

Separate the base from the top of the stand. Starting in the center, cut a strip of paper that is longer than the diameter of the circle. Gently bend the paper over the edges of the wood circle.

Use that fold as a guide for you to trim the paper strip. It may take a few attempts to get the paper to fit snugly on the circle. Brush a thin coat of Mod Podge down on the wood and smooth the paper on top of it.

striped-hook-for-bracelets

Create another strip of paper that will fit next to the first one by repeating the same process above to measure and cut the paper. Brush another line of glue and adhere the paper to the wood.

Depending on the thickness of the paper I was working with, sometimes the strip would slide under the prior stripe or over it. Repeat these steps to work your way across the entire wood circle.

After you covered the whole thing in paper stripes, go back and cover the surface with 1-2 thin coats of Mod Podge on top to protect the paper.

TIP: I decoupaged over the center hole where the top of the stand attached. Then, I just poked a hole through the paper afterwards so I could screw the top back on.

Step four: Decorate the ends of the hooks.

decorate-end-of-hooks-for-jewelry

Use a small circle punch (or scissors) to cut out coordinating paper decorations for the end of the cup hooks. Brush Mod Podge onto each one and attach a circle of paper. After they dry, brush another coat of decoupage onto of each circle to seal them.

Step five: Assemble and add your bracelets!

bracelet-storage-solution-hook

Once both pieces are dried and cured, reattach the rack onto the wood base. Find a cute place to set your stand and place your jewelry on it!

jewelry-storage-cup-holder-chip-dip

Enjoy your pretty, new DIY jewelry organizer! By the way, this stand matches another jewelry organizing project I made. . . a tray for my baubles from a glass chip-n-dip serving piece. Sigh, I just love cute storage!


Did you enjoy this great repurposed idea? If so, I’d love for you to check out these other projects:

Learn how to create a DIY plate wall display on a budget! In this project I used vintage photos for the perfect Mother's Day gift.
← Previous
DIY Plate Display Using Vintage Photos
Learn how to decorate a simple wood plant stand from the craft store using paper, decoupage medium, and adhesive stencils - AND it's waterproof!
Next →
Decoupage a Wood Plant Stand for Spring

bionicgeekgrrl

Tuesday 30th of July 2013

lovely, I recently picked one of these cup holders up cheap with similar intentions.

one idea I had was drilling a suitable hole in the bowl to combine the holder and trinket tray. tho might be tricky with ceramic, but plastic would be easy enough.

Emilley and Kate

Monday 16th of April 2012

This is such a beautiful idea! We will definitely have to try it!www.sewingaftersupper.blogspot.com.au

Sew Fun Design

Sunday 15th of April 2012

cute cute cute~~~~love it! got to go to the thrift store to find me one!

Onna

Saturday 14th of April 2012

I'm going to have to try this! Awesome!

Molly Jo

Saturday 14th of April 2012

I absolutely love this idea. I pinned it to remind me later this summer when I need crafts to keep busy!